www.pudn.com > Linux2410_device.rar > usbd-arch.h
/*
* linux/drivers/usbd/usbd-arch.h
*
* Copyright (c) 2000, 2001, 2002 Lineo
* Copyright (c) 2001 Hewlett Packard
*
* By:
* Stuart Lynne ,
* Tom Rushworth ,
* Bruce Balden
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
*/
/*
* This file contains pre-canned configurations for specific architectures
* and systems.
*
* The architecture specific areas concentrates on setting defaults that
* will work with each architecture (endpoint restrictions etc).
*
* The system specific areas set defaults appropriate for a specific
* system or board (vendor id etc).
*
* Typically during early development you will set these via the kernel
* configuration and migrate the values into here once specific values
* have been tested and will no longer change.
*/
/*
* Lineo specific
*/
#define VENDOR_SPECIFIC_CLASS 0xff
#define VENDOR_SPECIFIC_SUBCLASS 0xff
#define VENDOR_SPECIFIC_PROTOCOL 0xff
/*
* Lineo Classes
*/
#define LINEO_CLASS 0xff
#define LINEO_SUBCLASS_SAFENET 0x01
#define LINEO_SUBCLASS_SAFESERIAL 0x02
/*
* Lineo Protocols
*/
#define LINEO_SAFENET_CRC 0x01
#define LINEO_SAFENET_CRC_PADDED 0x02
#define LINEO_SAFESERIAL_CRC 0x01
#define LINEO_SAFESERIAL_CRC_PADDED 0x02
/*
* Architecture specific endpoint configurations
*/
#if defined(CONFIG_ARCH_SA1100) || defined(CONFIG_ARCH_SA1100_MODULE)
#warning
#warning SETTING DEFAULTS FOR SA1110
/*
* The StrongArm SA-1110 has fixed endpoints and the bulk endpoints
* are limited to 64 byte packets and does not support ZLP.
*/
#define ABS_OUT_ADDR 1
#define ABS_IN_ADDR 2
#define ABS_INT_ADDR 0
#define MAX_OUT_PKTSIZE 64
#define MAX_IN_PKTSIZE 64
#undef MAX_INT_PKTSIZE
#undef CONFIG_USBD_SERIAL_OUT_ENDPOINT
#undef CONFIG_USBD_SERIAL_IN_ENDPOINT
#undef CONFIG_USBD_SERIAL_INT_ENDPOINT
#define CONFIG_USBD_NO_ZLP_SUPPORT
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
#if defined(CONFIG_ARCH_L7200)|| defined(CONFIG_ARCH_L7200_MODULE)
#warning
#warning SETTING DEFAULTS FOR L7200
/*
* The Linkup L7205/L7210 has fixed endpoints and the bulk endpoints
* are limited to 32 byte packets and does not support ZLP.
*
* To get around specific hardware problems the Linkup eliminates optional
* strings in the configuration, reverses the CDC data interfaces.
*
* It also requires all USB packets sent and received to be padded. They
* must be either 31 or 32 bytes in length.
*
* XXX The new version of the L7210 may not require padding.
*/
#define ABS_OUT_ADDR 1
#define ABS_IN_ADDR 2
#define ABS_INT_ADDR 3
#define MAX_OUT_PKTSIZE 32
#define MAX_IN_PKTSIZE 32
#define MAX_INT_PKTSIZE 16
#undef CONFIG_USBD_SERIAL_OUT_ENDPOINT
#undef CONFIG_USBD_SERIAL_IN_ENDPOINT
#undef CONFIG_USBD_SERIAL_INT_ENDPOINT
#define CONFIG_USBD_NO_ZLP_SUPPORT
#define CONFIG_USBD_NET_NO_STRINGS
#define CONFIG_USBD_NET_PADDED
#define CONFIG_USBD_NET_CDC_DATA_REVERSED
#undef CONFIG_USBD_NET_CDC
#undef CONFIG_USBD_NET_MDLM
#undef CONFIG_USBD_NET_SAFE
#define CONFIG_USBD_NET_MDLM 1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
#if defined(CONFIG_USBD_SL11_BUS)|| defined(CONFIG_USBD_SL11_BUS_MODULE)
#warning
#warning SETTING DEFAULTS FOR SL11
/*
* The SL11 endpoints can be a mix of 1, 2, or 3. The SL11 endpoints have
* fixed addresses but each can be used for Bulk IN, Bulk OUT and Interrupt.
*
* The default addresses can be overridden by using the kernel configuration
* and setting the net-fd IN, OUT and INT addresses. See Config.in
*/
#define DFL_OUT_ADDR 1
#define DFL_IN_ADDR 2
#define DFL_INT_ADDR 3
#define MAX_OUT_ADDR 3
#define MAX_IN_ADDR 3
#define MAX_INT_ADDR 3
#define MAX_OUT_PKTSIZE 64
#define MAX_IN_PKTSIZE 64
#define MAX_INT_PKTSIZE 16
#endif
#if defined(CONFIG_USBD_SUPERH_BUS)|| defined(CONFIG_USBD_SUPERH_BUS_MODULE)
#warning
#warning SETTING DEFAULTS FOR SUPERH
/*
* The SuperH 7727 has fixed endpoints and does not support ZLP.
*/
#define ABS_OUT_ADDR 1
#define ABS_IN_ADDR 2
#define ABS_INT_ADDR 3
#define MAX_OUT_PKTSIZE 64
#define MAX_IN_PKTSIZE 64
#define MAX_INT_PKTSIZE 16
#undef CONFIG_USBD_NET_CDC
#undef CONFIG_USBD_NET_MDLM
#undef CONFIG_USBD_NET_SAFE
#define CONFIG_USBD_NET_MDLM 1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
#if defined(CONFIG_USBD_PXA_BUS)|| defined(CONFIG_USBD_PXA_BUS_MODULE)
#warning
#warning SETTING DEFAULTS FOR PXA
/*
* The PXA has fixed endpoints
*/
#define ABS_IN_ADDR 1
#define ABS_OUT_ADDR 2
#define ABS_INT_ADDR 5
#define MAX_OUT_PKTSIZE 64
#define MAX_IN_PKTSIZE 64
#define MAX_INT_PKTSIZE 8
#undef CONFIG_USBD_NET_CDC
#undef CONFIG_USBD_NET_MDLM
#undef CONFIG_USBD_NET_SAFE
#define CONFIG_USBD_NET_MDLM 1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
/* ********************************************************************************************* */
/*
* known vendor and product ids
* Serial and network vendor ids can be overidden with kernel config.
*/
/*
* For itsy we will use Compaq iPaq vendor ID and 0xffff for product id
*/
#if defined(CONFIG_SA1100_ITSY) || defined(CONFIG_SA1100_H3XXX) || defined(CONFIG_SA1100_ITSY_MODULE) || defined(CONFIG_SA1100_H3XXX_MODULE)
#warning CONFIGURING FOR IPAQ H3XXX
#undef CONFIG_USBD_VENDORID
#undef CONFIG_USBD_PRODUCTID
#define CONFIG_USBD_VENDORID 0x049f
#define CONFIG_USBD_PRODUCTID 0xffff
#undef CONFIG_USBD_VENDORID
#define CONFIG_USBD_VENDORID 0x04dd
#undef CONFIG_USBD_SERIAL_PRODUCTID
#define CONFIG_USBD_SERIAL_PRODUCTID 0x8001
#undef CONFIG_USBD_NET_PRODUCTID
#define CONFIG_USBD_NET_PRODUCTID 0x8003
#undef CONFIG_USBD_SELFPOWERED
#undef CONFIG_USBD_MANUFACTURER
#undef CONFIG_USBD_PRODUCT_NAME
#define CONFIG_USBD_SELFPOWERED 1
#define CONFIG_USBD_MANUFACTURER "Compaq"
#define CONFIG_USBD_PRODUCT_NAME "iPaq"
#undef CONFIG_USBD_NET_CDC
#undef CONFIG_USBD_NET_MDLM
#undef CONFIG_USBD_NET_SAFE
#define CONFIG_USBD_NET_MDLM 1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
/*
* Assigned vendor and product ids for HP Calypso
*/
#if defined(CONFIG_SA1100_CALYPSO) || defined(CONFIG_SA1110_CALYPSO) || defined(CONFIG_SA1100_CALYPSO_MODULE) || defined(CONFIG_SA1110_CALYPSO_MODULE)
#warning CONFIGURING FOR CALYPSO
#undef CONFIG_USBD_VENDORID
#undef CONFIG_USBD_PRODUCTID
#define CONFIG_USBD_VENDORID 0x03f0
#define CONFIG_USBD_PRODUCTID 0x2101
#undef CONFIG_USBD_SELFPOWERED
#undef CONFIG_USBD_MANUFACTURER
#undef CONFIG_USBD_PRODUCT_NAME
#define CONFIG_USBD_SELFPOWERED 1
#define CONFIG_USBD_MANUFACTURER "HP"
#define CONFIG_USBD_PRODUCT_NAME "Journada X25"
#endif
/*
* Assigned vendor and serial/network product ids for Sharp Iris
*/
#if defined(CONFIG_ARCH_L7200) && defined(CONFIG_IRIS) || defined(CONFIG_ARCH_L7200_MODULE) && defined(CONFIG_IRIS_MODULE)
#warning CONFIGURING FOR LINKUP
#undef CONFIG_USBD_VENDORID
#define CONFIG_USBD_VENDORID 0x04dd
#undef CONFIG_USBD_SERIAL_PRODUCTID
#define CONFIG_USBD_SERIAL_PRODUCTID 0x8001
#undef CONFIG_USBD_NET_PRODUCTID
#define CONFIG_USBD_NET_PRODUCTID 0x8003
#undef CONFIG_USBD_SELFPOWERED
#undef CONFIG_USBD_MANUFACTURER
#undef CONFIG_USBD_PRODUCT_NAME
#define CONFIG_USBD_SELFPOWERED 1
#define CONFIG_USBD_MANUFACTURER "Sharp"
#define CONFIG_USBD_PRODUCT_NAME "Iris"
#undef CONFIG_USBD_NET_CDC
#undef CONFIG_USBD_NET_MDLM
#undef CONFIG_USBD_NET_SAFE
#define CONFIG_USBD_NET_MDLM 1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
/*
* Assigned vendor and serial/network product ids for Sharp Collie
*/
#if defined(CONFIG_SA1100_COLLIE) || defined(CONFIG_SA1100_COLLIE_MODULE)
#warning CONFIGURING FOR COLLIE
#undef CONFIG_USBD_VENDORID
#define CONFIG_USBD_VENDORID 0x04dd
#undef CONFIG_USBD_SERIAL_PRODUCT ID
#define CONFIG_USBD_SERIAL_PRODUCT ID 0x8002
#undef CONFIG_USBD_NET_PRODUCTID
//#define CONFIG_USBD_NET_PRODUCTID 0x8004
#define CONFIG_USBD_NET_PRODUCTID 0x8003
#undef CONFIG_USBD_SELFPOWERED
#undef CONFIG_USBD_MANUFACTURER
#undef CONFIG_USBD_PRODUCT_NAME
#define CONFIG_USBD_SELFPOWERED 1
#define CONFIG_USBD_MANUFACTURER "Sharp"
#define CONFIG_USBD_PRODUCT_NAME "Zaurus"
#undef CONFIG_USBD_NET_CDC
#undef CONFIG_USBD_NET_MDLM
#undef CONFIG_USBD_NET_SAFE
#define CONFIG_USBD_NET_MDLM 1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
/*
* Assigned vendor and serial/network product ids for Vercel UD1
*/
#if defined(CONFIG_SA1100_IDR)
#warning CONFIGURING FOR Vercel UD1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif
#ifdef CONFIG_SABINAL_DISCOVERY
#warning CONFIGURING FOR DISCOVERY
#undef CONFIG_USBD_VENDORID
#define CONFIG_USBD_VENDORID 0x04dd
#undef CONFIG_USBD_SERIAL_PRODUCT ID
#define CONFIG_USBD_SERIAL_PRODUCT ID 0x8005
#undef CONFIG_USBD_NET_PRODUCTID
#define CONFIG_USBD_NET_PRODUCTID 0x8005
#undef CONFIG_USBD_SELFPOWERED
#undef CONFIG_USBD_MANUFACTURER
#undef CONFIG_USBD_PRODUCT_NAME
#define CONFIG_USBD_SELFPOWERED 1
#define CONFIG_USBD_MANUFACTURER "Sharp"
#define CONFIG_USBD_PRODUCT_NAME "SL-A300"
#undef CONFIG_USBD_NET_CDC
#undef CONFIG_USBD_NET_MDLM
#undef CONFIG_USBD_NET_SAFE
#define CONFIG_USBD_NET_MDLM 1
#define CONFIG_USBD_MAC_AS_SERIAL_NUMBER 1
#endif