www.pudn.com > Linux2410_device.rar > usbd-bi.h
/*
* linux/drivers/usbd/usbd-bi.h
*
* Copyright (c) 2000, 2001, 2002 Lineo
* Copyright (c) 2001 Hewlett Packard
*
* By:
* Stuart Lynne ,
* Tom Rushworth ,
* Bruce Balden
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
*/
#define MAX_DEVICES 1
/* struct udc_bi_data
*
* private data structure for this bus interface driver
*/
struct bi_data {
int num;
struct tq_struct cradle_bh;
};
extern unsigned int udc_interrupts;
extern int dbgflg_usbdbi_init;
extern int dbgflg_usbdbi_intr;
extern int dbgflg_usbdbi_tick;
extern int dbgflg_usbdbi_usbe;
extern int dbgflg_usbdbi_rx;
extern int dbgflg_usbdbi_tx;
extern int dbgflg_usbdbi_dma_flg;
extern int dbgflg_usbdbi_setup;
extern int dbgflg_usbdbi_ep0;
extern int dbgflg_usbdbi_udc;
extern int dbgflg_usbdbi_stall;
extern int dbgflg_usbdbi_pm;
extern int dbgflg_usbdbi_pur;
#define dbg_init(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_init,lvl,fmt,##args)
#define dbg_intr(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_intr,lvl,fmt,##args)
#define dbg_tick(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_tick,lvl,fmt,##args)
#define dbg_usbe(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_usbe,lvl,fmt,##args)
#define dbg_rx(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_rx,lvl,fmt,##args)
#define dbg_tx(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_tx,lvl,fmt,##args)
#define dbg_dmaflg(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_dma_flg,lvl,fmt,##args)
#define dbg_setup(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_setup,lvl,fmt,##args)
#define dbg_ep0(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_ep0,lvl,fmt,##args)
#define dbg_udc(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_udc,lvl,fmt,##args)
#define dbg_stall(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_stall,lvl,fmt,##args)
#define dbg_pm(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_pm,lvl,fmt,##args)
#define dbg_pur(lvl,fmt,args...) dbgPRINT(dbgflg_usbdbi_pur,lvl,fmt,##args)
/**
* udc_start_in_irq - start transmit
* @endpoint:
*
* Called with interrupts disabled.
*/
void udc_start_in_irq (struct usb_endpoint_instance *endpoint);
/**
* udc_stall_ep - stall endpoint
* @ep: physical endpoint
*
* Stall the endpoint.
*/
void udc_stall_ep (unsigned int ep);
/**
* udc_reset_ep - reset endpoint
* @ep: physical endpoint
* reset the endpoint.
*
* returns : 0 if ok, -1 otherwise
*/
void udc_reset_ep (unsigned int ep);
/**
* udc_endpoint_halted - is endpoint halted
* @ep:
*
* Return non-zero if endpoint is halted
*/
int udc_endpoint_halted (unsigned int ep);
/**
* udc_set_address - set the USB address for this device
* @address:
*
* Called from control endpoint function after it decodes a set address setup packet.
*/
void udc_set_address (unsigned char address);
/**
* udc_serial_init - set a serial number if available
*/
int __init udc_serial_init (struct usb_bus_instance *);
/**
* udc_max_endpoints - max physical endpoints
*
* Return number of physical endpoints.
*/
int udc_max_endpoints (void);
/**
* udc_check_ep - check logical endpoint
* @lep:
* @packetsize:
*
* Return physical endpoint number to use for this logical endpoint or zero if not valid.
*/
int udc_check_ep (int logical_endpoint, int packetsize);
/**
* udc_set_ep - setup endpoint
* @ep:
* @endpoint:
*
* Associate a physical endpoint with endpoint_instance
*/
void udc_setup_ep (struct usb_device_instance *device, unsigned int ep,
struct usb_endpoint_instance *endpoint);
/**
* udc_disable_ep - disable endpoint
* @ep:
*
* Disable specified endpoint
*/
void udc_disable_ep (unsigned int ep);
/**
* udc_connected - is the USB cable connected
*
* Return non-zeron if cable is connected.
*/
int udc_connected (void);
/**
* udc_connect - enable pullup resistor
*
* Turn on the USB connection by enabling the pullup resistor.
*/
void udc_connect (void);
/**
* udc_disconnect - disable pullup resistor
*
* Turn off the USB connection by disabling the pullup resistor.
*/
void udc_disconnect (void);
/**
* udc_all_interrupts - enable interrupts
*
* Switch on UDC interrupts.
*
*/
void udc_all_interrupts (struct usb_device_instance *);
/**
* udc_suspended_interrupts - enable suspended interrupts
*
* Switch on only UDC resume interrupt.
*
*/
void udc_suspended_interrupts (struct usb_device_instance *);
/**
* udc_disable_interrupts - disable interrupts.
*
* switch off interrupts
*/
void udc_disable_interrupts (struct usb_device_instance *);
/**
* udc_ep0_packetsize - return ep0 packetsize
*/
int udc_ep0_packetsize (void);
/**
* udc_enable - enable the UDC
*
* Switch on the UDC
*/
void udc_enable (struct usb_device_instance *device);
/**
* udc_disable - disable the UDC
*
* Switch off the UDC
*/
void udc_disable (void);
/**
* udc_startup - allow udc code to do any additional startup
*/
void udc_startup (struct usb_device_instance *device);
/**
* udc_startup - allow udc code to do any additional startup
*/
void udc_startup_events (struct usb_device_instance *);
/**
* udc_init - initialize USB Controller
*
* Get ready to use the USB Controller.
*
* Register an interrupt handler and IO region. Return non-zero for error.
*/
int udc_init (void);
/**
* udc_exit - Stop using the USB Controller
*
* Stop using the USB Controller.
*
* Shutdown and free dma channels, de-register the interrupt handler.
*/
void udc_exit (void);
/**
* udc_regs - dump registers
*
* Dump registers with printk
*/
void udc_regs (void);
/**
* udc_name - return name of USB Device Controller
*/
char *udc_name (void);
/**
* udc_request_udc_irq - request UDC interrupt
*
* Return non-zero if not successful.
*/
int udc_request_udc_irq (void);
/**
* udc_request_cable_irq - request Cable interrupt
*
* Return non-zero if not successful.
*/
int udc_request_cable_irq (void);
/**
* udc_request_udc_io - request UDC io region
*
* Return non-zero if not successful.
*/
int udc_request_io (void);
/**
* udc_release_udc_irq - release UDC irq
*/
void udc_release_udc_irq (void);
/**
* udc_release_cable_irq - release Cable irq
*/
void udc_release_cable_irq (void);
/**
* udc_release_io - release UDC io region
*/
void udc_release_io (void);
/**
* udc_connect_event - called from cradle interrupt handler
* @connected - true if we are in cradle
*/
void udc_cable_event (void);
void udc_ticker_poke (void);