www.pudn.com > tomcat-5.5.9.rar > workers.properties, change:2005-10-21,size:5864b


# workers.properties - 
# 
# This file provides jk derived plugins with the needed information to 
# connect to the different tomcat workers.  Note that the distributed 
# version of this file requires modification before it is usable by a 
# plugin. 
# 
# As a general note, the characters $( and ) are used internally to define 
# macros. Do not use them in your own configuration!!! 
# 
# Whenever you see a set of lines such as: 
# x=value 
# y=$(x)\something 
# 
# the final value for y will be value\something 
# 
# Normaly all you will need to do is un-comment and modify the first three 
# properties, i.e. workers.tomcat_home, workers.java_home and ps. 
# Most of the configuration is derived from these. 
# 
# When you are done updating workers.tomcat_home, workers.java_home and ps 
# you should have 3 workers configured: 
# 
# - An ajp12 worker that connects to localhost:8007 
# - An ajp13 worker that connects to localhost:8009 
# - A jni inprocess worker. 
# - A load balancer worker 
# 
# However by default the plugins will only use the ajp12 worker. To have 
# the plugins use other workers you should modify the worker.list property. 
# 
# 
 
# OPTIONS ( very important for jni mode )  
 
# 
# workers.tomcat_home should point to the location where you 
# installed tomcat. This is where you have your conf, webapps and lib 
# directories. 
# 
workers.tomcat_home=/var/tomcat3 
 
# 
# workers.java_home should point to your Java installation. Normally 
# you should have a bin and lib directories beneath it. 
# 
workers.java_home=/opt/IBMJava2-13 
 
# 
# You should configure your environment slash... ps=\ on NT and / on UNIX 
# and maybe something different elsewhere. 
# 
ps=/ 
 
# 
#------ ADVANCED MODE ------------------------------------------------ 
#--------------------------------------------------------------------- 
# 
 
# 
#------ DEFAULT worket list ------------------------------------------ 
#--------------------------------------------------------------------- 
# 
# 
# The workers that your plugins should create and work with 
# 
# Add 'inprocess' if you want JNI connector  
worker.list=ajp12, ajp13 
# , inprocess 
 
 
# 
#------ DEFAULT ajp12 WORKER DEFINITION ------------------------------ 
#--------------------------------------------------------------------- 
# 
 
# 
# Defining a worker named ajp12 and of type ajp12 
# Note that the name and the type do not have to match. 
# 
worker.ajp12.port=8007 
worker.ajp12.host=localhost 
worker.ajp12.type=ajp12 
# 
# Specifies the load balance factor when used with 
# a load balancing worker. 
# Note: 
#  ----> lbfactor must be > 0 
#  ----> Low lbfactor means less work done by the worker. 
worker.ajp12.lbfactor=1 
 
# 
#------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ 
#--------------------------------------------------------------------- 
# 
 
# 
# Defining a worker named ajp13 and of type ajp13 
# Note that the name and the type do not have to match. 
# 
worker.ajp13.port=8009 
worker.ajp13.host=localhost 
worker.ajp13.type=ajp13 
# 
# Specifies the load balance factor when used with 
# a load balancing worker. 
# Note: 
#  ----> lbfactor must be > 0 
#  ----> Low lbfactor means less work done by the worker. 
worker.ajp13.lbfactor=1 
 
# 
# Specify the size of the open connection cache. 
#worker.ajp13.cachesize 
 
# 
#------ DEFAULT LOAD BALANCER WORKER DEFINITION ---------------------- 
#--------------------------------------------------------------------- 
# 
 
# 
# The loadbalancer (type lb) workers perform wighted round-robin 
# load balancing with sticky sessions. 
# Note: 
#  ----> If a worker dies, the load balancer will check its state 
#        once in a while. Until then all work is redirected to peer 
#        workers. 
worker.loadbalancer.type=lb 
worker.loadbalancer.balanced_workers=ajp12, ajp13 
 
 
# 
#------ DEFAULT JNI WORKER DEFINITION--------------------------------- 
#--------------------------------------------------------------------- 
# 
 
# 
# Defining a worker named inprocess and of type jni 
# Note that the name and the type do not have to match. 
# 
worker.inprocess.type=jni 
 
# 
#------ CLASSPATH DEFINITION ----------------------------------------- 
#--------------------------------------------------------------------- 
# 
 
# 
# Additional class path components. 
# 
worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)tomcat.jar 
 
# 
# Setting the command line for tomcat.  
# Note: The cmd_line string may not contain spaces. 
# 
worker.inprocess.cmd_line=start 
 
# Not needed, but can be customized. 
#worker.inprocess.cmd_line=-config 
#worker.inprocess.cmd_line=$(workers.tomcat_home)$(ps)conf$(ps)server.xml 
#worker.inprocess.cmd_line=-home 
#worker.inprocess.cmd_line=$(workers.tomcat_home) 
 
# 
# The JVM that we are about to use 
# 
# This is for Java2 
# 
# Windows 
worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)jvm.dll 
# IBM JDK1.3  
#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)libjvm.so 
# Unix - Sun VM or blackdown 
#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)lib$(ps)i386$(ps)classic$(ps)libjvm.so 
 
# 
# And this is for jdk1.1.X 
# 
#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)bin$(ps)javai.dll 
 
 
# 
# Setting the place for the stdout and stderr of tomcat 
# 
worker.inprocess.stdout=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stdout 
worker.inprocess.stderr=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stderr 
 
# 
# Setting the tomcat.home Java property 
# 
#worker.inprocess.sysprops=tomcat.home=$(workers.tomcat_home) 
 
# 
# Java system properties 
# 
# worker.inprocess.sysprops=java.compiler=NONE 
# worker.inprocess.sysprops=myprop=mypropvalue 
 
# 
# Additional path components. 
# 
# worker.inprocess.ld_path=d:$(ps)SQLLIB$(ps)bin 
#