www.pudn.com > art_v46.zip > ar5002x_mb32ag.eep
#$Id: //depot/sw/branches/ART_V45/bringup/ar5k/config/ar5002x_mb32ag.eep#3 $ #EEPROM file for AR5002X 802.11a/b/g MiniPCI Reference Design card @cal_section_begin # begin @cal section TARGET_POWER_FILENAME = calTrgtPwr_ar5002x_mb32ag.txt ; # target power file for calibration SUBSYSTEM_ID = 0x2031; # Subsystem ID in hex EEPROM_MAP_TYPE = 1; # Flag indicating eeprom layout type TURBO_DISABLE = 0; # Prevents software from using TURBO modes RF_SILENT = 0; # Cards enabled with RFSilent can be easily silenced DEVICE_TYPE = 3; # 1=>Cardbus, 2=>PCI, 3=>miniPCI, 4=>AP TURBO_MAXPOWER_5G = 16.0; # Recommended max power in turbo mode to consume less than 2W. TURBO_MAXPOWER_2p5G = 16.0; # Recommended max power in turbo mode at 2.5 GHz to consume less than 2W. A_MODE = 1; # Whether the adapter supports 802.11a functionality B_MODE = 1; # Whether the adapter supports 802.11b functionality G_MODE = 1; # Whether the adapter supports 802.11g functionality ANTENNA_GAIN_5G = 0; # Antenna gain at 5.5GHz. 8-bit signed val in 0.5dB steps. ANTENNA_GAIN_2p5G = 0; # Antenna gain at 2.5GHz. 8-bit signed val in 0.5dB steps. XLNA_GAIN = 13; # xLNA gain in dB (per AS 6/14/02) NOISE_FLOOR_THRESHOLD = -54; # noise floor threshold value (per JHfmn 6/14/02) 11b_XLNA_GAIN = 13; # xLNA gain in dB 11b_NOISE_FLOOR_THRESHOLD = -1; # noise floor threshold value 11g_XLNA_GAIN = 13; # xLNA gain in dB 11g_NOISE_FLOOR_THRESHOLD = -1; # noise floor threshold value 11a_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap. 11b_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap. 11g_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap. 11g_TURBO_DISABLE = 0; # Set to 1 to disable TURBO mode in 11g CCK_OFDM_DELTA = 1; # in dB with 0.1dB resolution. In 11g, delta in output power for 1mbps and 6mbps # for any given pcdac. CH14_FILTER_CCK_DELTA = 1.5; # in dB with 0.1dB resolution. In 11g & 11b, delta in output power for ch14 and ch1 - ch13 # for any given pcdac. This delta arises due to special filter requirement for ch14 (2484). ENABLE_32KHZ = 0; # Flag indicating the presence of the 32kHz sleep crystal @cal_section_end # end @cal section @config_section_begin # begin @config section #Antenna Switch Table #6 bit (msb:lsb) value are mapped to [atten5, atten2, antD, antC, antB, antA] #---------------------------------------------------------------------------------- @MODE: MODE_SPECIFIC 11a 11a_turbo 11b 11g 11g_tubo #---------------------------------------------------------------------------------- bb_switch_table_r1x12 0x00 0x00 0x01 0x01 0x01 #(AntCtl 5) bb_switch_table_r1x2 0x00 0x00 0x01 0x01 0x01 #(AntCtl 4) bb_switch_table_r1x1 0x00 0x00 0x01 0x01 0x01 #(AntCtl 3) bb_switch_table_r1 0x01 0x01 0x11 0x11 0x11 #(AntCtl 2) bb_switch_table_t1 0x02 0x02 0x02 0x02 0x02 #(AntCtl 1) bb_switch_table_r2x12 0x00 0x00 0x02 0x02 0x02 #(AntCtl 10) bb_switch_table_r2x2 0x00 0x00 0x02 0x02 0x02 #(AntCtl 9) bb_switch_table_r2x1 0x00 0x00 0x02 0x02 0x02 #(AntCtl 8) bb_switch_table_r2 0x02 0x02 0x12 0x12 0x12 #(AntCtl 7) bb_switch_table_t2 0x01 0x01 0x01 0x01 0x01 #(AntCtl 6) bb_rxtx_margin_2ghz 0 0 27 27 27 bb_switch_settling 0x2d 0x5a 0x31 0x31 0x31 bb_txrxatten 15 15 30 30 30 bb_pga_desired_size -80 -80 -80 -80 -80 bb_adc_desired_size -32 -32 -38 -32 -32 rf_ob 2 2 2 2 2 rf_db 2 2 2 2 2 rf_b_ob 2 2 2 2 2 rf_b_db 2 2 2 2 2 rf_xpdsel 1 1 1 1 1 rf_pdgain_lo 0x0 0x0 0x0 0x0 0x0 rf_pdgain_hi 0x0 0x0 0x0 0x0 0x0 #rf_pdgain_hi 0x3 0x3 0x3 0x3 0x3 bb_thresh62 15 15 28 28 28 bb_tx_end_to_xpab_off 0 0 0 0 0 bb_tx_end_to_xpaa_off 0 0 0 0 0 bb_tx_frame_to_xpab_on 0x0e 0xe 0x7 0xe 0xe bb_tx_frame_to_xpaa_on 0x0e 0xe 0x7 0xe 0xe bb_tx_end_to_xlna_on 2 2 2 2 2 rf_gain_I 0x0a 0x0a 0x0a 0x0a 0x0a @config_section_end # end @config section