www.pudn.com > art_v46.zip > ar5001x2_mb22g.eep
#$Id: //depot/sw/branches/ART_V45/bringup/ar5k/config/ar5001x2_mb22g.eep#2 $
#EEPROM file for AR5001X+ 802.11b/g MiniPCI Basic Reference Design (11a front end depopulated)
@cal_section_begin # begin @cal section
TARGET_POWER_FILENAME = calTrgtPwr_ar5001x2_mb22g.txt ; # target power file for calibration
SUBSYSTEM_ID = 0x2027; # Subsystem ID in hex
TURBO_DISABLE = 0; # Prevents software from using TURBO modes
RF_SILENT = 0; # Cards enabled with RFSilent can be easily silenced
DEVICE_TYPE = 3; # 1=>Cardbus, 2=>PCI, 3=>miniPCI, 4=>AP
TURBO_MAXPOWER_5G = 16.0; # Recommended max power in turbo mode to consume less than 2W.
TURBO_MAXPOWER_2p5G = 16.0; # Recommended max power in turbo mode at 2.5 GHz to consume less than 2W.
A_MODE = 0; # Whether the adapter supports 802.11a functionality
B_MODE = 1; # Whether the adapter supports 802.11b functionality
G_MODE = 1; # Whether the adapter supports 802.11g functionality
ANTENNA_GAIN_5G = 0; # Antenna gain at 5.5GHz. 8-bit signed val in 0.5dB steps.
ANTENNA_GAIN_2p5G = 0; # Antenna gain at 2.5GHz. 8-bit signed val in 0.5dB steps.
XLNA_GAIN = 13; # xLNA gain in dB (per AS 6/14/02)
NOISE_FLOOR_THRESHOLD = -54; # noise floor threshold value (per JHfmn 6/14/02)
11b_XLNA_GAIN = 13; # xLNA gain in dB
11b_NOISE_FLOOR_THRESHOLD = -1; # noise floor threshold value
11g_XLNA_GAIN = 13; # xLNA gain in dB
11g_NOISE_FLOOR_THRESHOLD = -1; # noise floor threshold value
11a_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap.
11b_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap.
11g_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap.
11g_TURBO_DISABLE = 0; # Set to 1 to disable TURBO mode in 11g
CCK_OFDM_DELTA = 1.5; # in dB with 0.1dB resolution. In 11g, delta in output power for 1mbps and 6mbps
# for any given pcdac.
CH14_FILTER_CCK_DELTA = 1.5; # in dB with 0.1dB resolution. In 11g & 11b, delta in output power for ch14 and ch1 - ch13
# for any given pcdac. This delta arises due to special filter requirement for ch14 (2484).
@cal_section_end # end @cal section
@config_section_begin # begin @config section
#Antenna Switch Table
#6 bit (msb:lsb) value are mapped to [atten5, atten2, antD, antC, antB, antA]
#----------------------------------------------------------------------------------
@MODE: MODE_SPECIFIC 11a 11a_turbo 11b 11g 11g_turbo
#----------------------------------------------------------------------------------
bb_switch_table_r1x12 0 0 0x20 0x20 0x20 #(AntCtl 5)
bb_switch_table_r1x2 0 0 0x10 0x10 0x10 #(AntCtl 4)
bb_switch_table_r1x1 0 0 0x24 0x24 0x24 #(AntCtl 3)
bb_switch_table_r1 0 0 0x14 0x14 0x14 #(AntCtl 2)
bb_switch_table_t1 0 0 0x28 0x28 0x28 #(AntCtl 1)
bb_switch_table_r2x12 0 0 0x20 0x20 0x20 #(AntCtl 10)
bb_switch_table_r2x2 0 0 0x10 0x10 0x10 #(AntCtl 9)
bb_switch_table_r2x1 0 0 0x28 0x28 0x28 #(AntCtl 8)
bb_switch_table_r2 0 0 0x18 0x18 0x18 #(AntCtl 7)
bb_switch_table_t2 0 0 0x24 0x24 0x24 #(AntCtl 6)
bb_rxtx_margin_2ghz 11 11 16 16 16
bb_switch_settling 0 0 0x23 0x2d 0x5a
bb_txrxatten 0 0 15 15 15
bb_pga_desired_size 0 0 -80 -80 -80
bb_adc_desired_size 0 0 -38 -32 -32
rf_b_ob 0 0 4 3 3
rf_b_db 0 0 4 3 3
rf_ob 0 0 2 2 2
rf_db 0 0 2 2 2
rf_plo_sel 0 0 1 1 1
rf_pwdxpd 0 0 0 0 0
rf_xpd_gain 0 0 0xb 0xb 0xb
bb_thresh62 0 0 28 28 28
bb_tx_end_to_xpab_off 0 0 0 0 0
bb_tx_end_to_xpaa_off 0 0 0 0 0
bb_tx_frame_to_xpab_on 0 0 0x7 0xe 0xe
bb_tx_frame_to_xpaa_on 0 0 0x7 0xe 0xe
bb_tx_end_to_xlna_on 0 0 2 2 2
rf_gain_I 0 0 0x0a 0x0a 0x0a
@config_section_end # end @config section