www.pudn.com > art_v46.zip > ar5001x2_cb21g.eep
#$Id: //depot/sw/branches/ART_V45/bringup/ar5k/config/ar5001x2_cb21g.eep#2 $ #EEPROM file for AR5001X+ 802.11b/g CardBus Revised Reference (new layout) @cal_section_begin # begin @cal section TARGET_POWER_FILENAME = calTrgtPwr_ar5001x2_cb21g.txt; # target power file for calibration SUBSYSTEM_ID = 0x1025; # Subsystem ID in hex TURBO_DISABLE = 0; # Prevents software from using TURBO modes in 11a RF_SILENT = 0; # Cards enabled with RFSilent can be easily silenced DEVICE_TYPE = 1; # 1=>Cardbus, 2=>PCI, 3=>miniPCI, 4=>AP TURBO_MAXPOWER_5G = 0; # Recommended max power in turbo mode to consume less than 2W. TURBO_MAXPOWER_2p5G = 16.0; # Recommended max power in turbo mode at 2.5 GHz to consume less than 2W. A_MODE = 0; # Whether the adapter supports 802.11a functionality B_MODE = 1; # Whether the adapter supports 802.11b functionality G_MODE = 1; # Whether the adapter supports 802.11g functionality ANTENNA_GAIN_5G = 0; # Antenna gain at 5GHz. 8-bit signed val in 0.5dB steps. ANTENNA_GAIN_2p5G = 1; # Antenna gain at 2.5GHz. 8-bit signed val in 0.5dB steps. XLNA_GAIN = 0; # xLNA gain in dB (per AS 6/14/02) NOISE_FLOOR_THRESHOLD = -1; # noise floor threshold value (per JHfmn 6/14/02) 11b_XLNA_GAIN = 13; # xLNA gain in dB 11b_NOISE_FLOOR_THRESHOLD = -1; # noise floor threshold value 11g_XLNA_GAIN = 13; # xLNA gain in dB 11g_NOISE_FLOOR_THRESHOLD = -1; # noise floor threshold value 11a_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap. 11b_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap. 11g_FALSE_DETECT_BACKOFF = 0; # in dB. only affects channels w/ clock harmonic overlap. 11g_TURBO_DISABLE = 0; # Set to 1 to disable TURBO mode in 11g 11g_TURBO_DISABLE = 0; # Set to 1 to disable TURBO mode in 11g CCK_OFDM_DELTA = 1.5; # in dB with 0.1dB resolution. In 11g, delta in output power for 1mbps and 6mbps # for any given pcdac. CH14_FILTER_CCK_DELTA = 1.5; # in dB with 0.1dB resolution. In 11g & 11b, delta in output power for ch14 and ch1 - ch13 # for any given pcdac. This delta arises due to special filter requirement for ch14 (2484). @cal_section_end # end @cal section @config_section_begin # begin @config section #Antenna Switch Table #6 bit (msb:lsb) value are mapped to [atten5, atten2, antD, antC, antB, antA] #---------------------------------------------------------------------------------- @MODE: MODE_SPECIFIC 11a 11a_turbo 11b 11g 11g_turbo #---------------------------------------------------------------------------------- bb_switch_table_r1x12 0x00 0x00 0x20 0x20 0x20 #(AntCtl 5) bb_switch_table_r1x2 0x00 0x00 0x10 0x10 0x10 #(AntCtl 4) bb_switch_table_r1x1 0x00 0x00 0x2a 0x2a 0x2a #(AntCtl 3) bb_switch_table_r1 0x00 0x00 0x1a 0x1a 0x1a #(AntCtl 2) bb_switch_table_t1 0x00 0x00 0x25 0x25 0x25 #(AntCtl 1) bb_switch_table_r2x12 0x00 0x00 0x20 0x20 0x20 #(AntCtl 10) bb_switch_table_r2x2 0x00 0x00 0x10 0x10 0x10 #(AntCtl 9) bb_switch_table_r2x1 0x00 0x00 0x25 0x25 0x25 #(AntCtl 8) bb_switch_table_r2 0x00 0x00 0x15 0x15 0x15 #(AntCtl 7) bb_switch_table_t2 0x00 0x00 0x2a 0x2a 0x2a #(AntCtl 6) bb_rxtx_margin_2ghz 11 11 16 16 16 bb_switch_settling 0x00 0x00 0x2d 0x2d 0x5a bb_txrxatten 0x00 0x00 15 15 15 bb_pga_desired_size 0x00 0x00 -80 -80 -80 bb_adc_desired_size 0x00 0x00 -38 -32 -32 rf_b_ob 0x00 0x00 4 3 3 rf_b_db 0x00 0x00 4 3 3 rf_ob 0x00 0x00 2 2 2 rf_db 0x00 0x00 2 2 2 rf_plo_sel 0x00 0x00 1 1 1 rf_pwdxpd 0x00 0x00 0 0 0 rf_xpd_gain 0x00 0x00 0xb 0xb 0xb bb_thresh62 0x00 0x00 28 28 28 bb_tx_end_to_xpab_off 0x00 0x00 0 0 0 bb_tx_end_to_xpaa_off 0x00 0x00 0 0 0 bb_tx_frame_to_xpab_on 0x00 0x00 0x7 0xe 0xe bb_tx_frame_to_xpaa_on 0x00 0x00 0x7 0xe 0xe bb_tx_end_to_xlna_on 0x00 0x00 2 2 2 rf_gain_I 0x0a 0x0a 0x0a 0x0a 0x0a @config_section_end # end @config section