www.pudn.com > art_v46.zip > ar5001a2_cb21.eep
#$Id: //depot/sw/branches/ART_V45/bringup/ar5k/config/ar5001a2_cb21.eep#1 $ #EEPROM file for AR5001A+ 802.11a Cardbus Reference Design @cal_section_begin # begin @cal section TARGET_POWER_FILENAME = calTrgtPwr_ar5001a2_cb21.txt; # target power filename for calibration SUBSYSTEM_ID = 0x1028; # Subsystem ID in hex TURBO_DISABLE = 0; # Prevents software from using TURBO modes RF_SILENT = 0; # Cards enabled with RFSilent can be easily silenced DEVICE_TYPE = 1; # 1=>Cardbus, 2=>PCI, 3=>miniPCI, 4=>AP TURBO_MAXPOWER_5G = 16.0; # Recommended max power in turbo mode to consume less than 2W. A_MODE = 1; # Whether the adapter supports 802.11a functionality B_MODE = 0; # Whether the adapter supports 802.11b functionality G_MODE = 0; # Whether the adapter supports 802.11g functionality ANTENNA_GAIN_5G = 2; # Antenna gain at 5.5GHz. 8-bit signed val in 0.5dB steps. XLNA_GAIN = 13; # xLNA gain in dB (per AS 6/14/02) NOISE_FLOOR_THRESHOLD = -54; # noise floor threshold value 11a_FALSE_DETECT_BACKOFF = 1; # in dB. only affects channels w/ clock harmonic overlap. @cal_section_end # end @cal section @config_section_begin # begin @config section #Antenna Switch Table #6 bit (msb:lsb) value are mapped to [atten5, atten2, antD, antC, antB, antA] #------------------------------------------------------------------------------ @MODE: MODE_SPECIFIC 11a 11a_turbo 11b 11g #------------------------------------------------------------------------------ bb_switch_table_r1x12 0x12 0x12 0 0 #(AntCtl 5) bb_switch_table_r1x2 0x22 0x22 0 0 #(AntCtl 4) bb_switch_table_r1x1 0x12 0x12 0 0 #(AntCtl 3) bb_switch_table_r1 0x22 0x22 0 0 #(AntCtl 2) bb_switch_table_t1 0x18 0x18 0 0 #(AntCtl 1) bb_switch_table_r2x12 0x18 0x18 0 0 #(AntCtl 10) bb_switch_table_r2x2 0x28 0x28 0 0 #(AntCtl 9) bb_switch_table_r2x1 0x18 0x18 0 0 #(AntCtl 8) bb_switch_table_r2 0x28 0x28 0 0 #(AntCtl 7) bb_switch_table_t2 0x12 0x12 0 0 #(AntCtl 6) bb_rxtx_margin_2ghz 11 11 0 0 bb_switch_settling 0x2d 0x5a 0 0 bb_txrxatten 7 7 0 0 bb_pga_desired_size -80 -80 0 0 bb_adc_desired_size -32 -32 0 0 rf_b_ob 1 1 0 0 rf_b_db 1 1 0 0 rf_ob 1 1 0 0 rf_db 2 2 0 0 rf_plo_sel 1 1 0 0 rf_pwdxpd 0 0 0 0 rf_xpd_gain 0xd 0xd 0 0 bb_thresh62 15 15 0 0 bb_tx_end_to_xpab_off 0 0 0 0 bb_tx_end_to_xpaa_off 0 0 0 0 bb_tx_frame_to_xpab_on 0x0e 0xe 0 0 bb_tx_frame_to_xpaa_on 0x0e 0xe 0 0 bb_tx_end_to_xlna_on 2 2 0 0 rf_gain_I 0x0a 0x0a 0x0a 0x0a @config_section_end # end @config section