www.pudn.com > CPLD_PWM.rar > PWM.PIN
-- Copyright (C) 1991-2005 Altera Corporation -- Your use of Altera Corporation's design tools, logic functions -- and other software and tools, and its AMPP partner logic -- functions, and any output files any of the foregoing -- (including device programming or simulation files), and any -- associated documentation or information are expressly subject -- to the terms and conditions of the Altera Program License -- Subscription Agreement, Altera MegaCore Function License -- Agreement, or other applicable license agreement, including, -- without limitation, that your use is for the sole purpose of -- programming logic devices manufactured by Altera and sold by -- Altera or its authorized distributors. Please refer to the -- applicable agreement for further details. -- -- This is a Quartus II output file. It is for reporting purposes only, and is -- not intended for use as a Quartus II input file. This file cannot be used -- to make Quartus II pin assignments - for instructions on how to make pin -- assignments, please see Quartus II help. --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- -- NC : No Connect. This pin has no internal connection to the device. -- VCC : Dedicated power pin, which MUST be connected to VCC. -- VCCIO : Dedicated power pin, which MUST be connected to VCC -- of its bank. -- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND. -- It can also be used to report unused dedicated pins. The connection -- on the board for unused dedicated pins depends on whether this will -- be used in a future design. One example is device migration. When -- using device migration, refer to the device pin-tables. If it is a -- GND pin in the pin table or if it will not be used in a future design -- for another purpose the it MUST be connected to GND. If it is an unused -- dedicated pin, then it can be connected to a valid signal on the board -- (low, high, or toggling) if that signal is required for a different -- revision of the design. -- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins. -- This pin should be connected to GND. It may also be connected to a -- valid signal on the board (low, high, or toggling) if that signal -- is required for a different revision of the design. -- GND* : Unused I/O pin. This pin can either be left unconnected or -- connected to GND. Connecting this pin to GND will improve the -- device's immunity to noise. -- RESERVED : Unused I/O pin, which MUST be left unconnected. -- RESERVED_INPUT : Pin is tri-stated and should be connected to the board. -- NON_MIGRATABLE: This pin cannot be migrated. --------------------------------------------------------------------------------- Quartus II Version 5.0 Build 148 04/26/2005 SJ Full Version CHIP "pwm" ASSIGNED TO AN: EPM7128SLC84-15 Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment ------------------------------------------------------------------------------------------------------------- GND+ : 1 : : : : : GND+ : 2 : : : : : VCCINT : 3 : power : : 5.0V : : RESERVED : 4 : : : : : RESERVED : 5 : : : : : RESERVED : 6 : : : : : GND : 7 : gnd : : : : cs[0] : 8 : output : TTL : : : Y cs[1] : 9 : output : TTL : : : Y cs[2] : 10 : output : TTL : : : Y cs[3] : 11 : output : TTL : : : Y led[0] : 12 : output : TTL : : : Y VCCIO : 13 : power : : 5.0V : : TDI : 14 : input : TTL : : : N led[1] : 15 : output : TTL : : : Y led[2] : 16 : output : TTL : : : Y led[3] : 17 : output : TTL : : : Y led[4] : 18 : output : TTL : : : Y GND : 19 : gnd : : : : led[5] : 20 : output : TTL : : : Y led[6] : 21 : output : TTL : : : Y led[7] : 22 : output : TTL : : : Y TMS : 23 : input : TTL : : : N RESERVED : 24 : : : : : RESERVED : 25 : : : : : VCCIO : 26 : power : : 5.0V : : RESERVED : 27 : : : : : RESERVED : 28 : : : : : RESERVED : 29 : : : : : RESERVED : 30 : : : : : RESERVED : 31 : : : : : GND : 32 : gnd : : : : key[0] : 33 : input : TTL : : : Y RESERVED : 34 : : : : : key[1] : 35 : input : TTL : : : Y RESERVED : 36 : : : : : RESERVED : 37 : : : : : VCCIO : 38 : power : : 5.0V : : RESERVED : 39 : : : : : RESERVED : 40 : : : : : RESERVED : 41 : : : : : GND : 42 : gnd : : : : VCCINT : 43 : power : : 5.0V : : RESERVED : 44 : : : : : RESERVED : 45 : : : : : RESERVED : 46 : : : : : GND : 47 : gnd : : : : RESERVED : 48 : : : : : RESERVED : 49 : : : : : RESERVED : 50 : : : : : RESERVED : 51 : : : : : RESERVED : 52 : : : : : VCCIO : 53 : power : : 5.0V : : RESERVED : 54 : : : : : RESERVED : 55 : : : : : RESERVED : 56 : : : : : RESERVED : 57 : : : : : RESERVED : 58 : : : : : GND : 59 : gnd : : : : RESERVED : 60 : : : : : RESERVED : 61 : : : : : TCK : 62 : input : TTL : : : N RESERVED : 63 : : : : : RESERVED : 64 : : : : : RESERVED : 65 : : : : : VCCIO : 66 : power : : 5.0V : : RESERVED : 67 : : : : : RESERVED : 68 : : : : : RESERVED : 69 : : : : : RESERVED : 70 : : : : : TDO : 71 : output : TTL : : : N GND : 72 : gnd : : : : RESERVED : 73 : : : : : RESERVED : 74 : : : : : diode[4] : 75 : output : TTL : : : Y diode[3] : 76 : output : TTL : : : Y diode[2] : 77 : output : TTL : : : Y VCCIO : 78 : power : : 5.0V : : diode[1] : 79 : output : TTL : : : Y diode[0] : 80 : output : TTL : : : Y pwm_out : 81 : output : TTL : : : Y GND : 82 : gnd : : : : clk : 83 : input : TTL : : : Y GND+ : 84 : : : : :