www.pudn.com > nxplpc2204bsp.rar > config.h
/* config.h - WindRiver SBC ARM7TDMI configuration header */
/* Copyright 1984-2001 Wind River Systems, Inc. */
#include "copyright_wrs.h"
/*
modification history
--------------------
01o,23jul04,a_m BSP定制 for 精英arm7开发板
01n,16jul02,m_h C++ protection
01m,09may02,m_h New rev for PHY changes
01l,19dec01,m_h FLASH_CHIP_WIDTH needed for new version flash functions
01k,30nov01,m_h increase ROM_SIZE for ROM resident images
01j,27sep01,m_h bump revision for big endian support
01i,24aug01,m_h SPR 69508, boot line
01h,23jul01,m_h builds on UNIX
01g,17jul01,g_h add support for visionWARE 2.00
01f,10jul01,g_h add INCLUDE_LCD & INCLUDE_LED & INCLUDE_NETWORK macros
01e,06jun01,m_h flash cache issues
01d,16may01,m_h default baud now 9600
01c,01may01,m_h bump revision to 10
01b,26apr01,m_h convert tabs to spaces for readability
01a,12apr01,m_h created from snds100 template.
*/
/*
This module contains the configuration parameters for the SBC ARM7TDMI BSP.
*/
#ifndef INCconfigh
#define INCconfigh
#ifdef __cplusplus
extern "C" {
#endif
/* BSP version/revision identification, before configAll.h */
#define BSP_VER_1_1 1 /* 1.2 is backward compatible with 1.1 */
#define BSP_VER_1_2 1
#define BSP_VERSION "1.2"
#define BSP_REV "/19" /* BSP revision */
#include "configAll.h"
/*
* STANDALONE_NET must be defined for network debug with
* standalone vxWorks
*/
#undef STANDALONE_NET
/*
* Define SERIAL_DEBUG to enable debugging
* via the serial ports
*/
#undef SERIAL_DEBUG
/*
* If the FORCE_DEFAULT_BOOT_LINE is defined then the DEFAULT_BOOT_LINE
* parameters are always used regardless of NVRAM values specified at
* bootrom time. See target.nr for details. This is usually used to debug
* downloaded images with out a bootrom present.
*/
#define FORCE_DEFAULT_BOOT_LINE /* : undef->define */
#ifdef INCLUDE_WDB_COMM_VTMD
#define FORCE_DEFAULT_BOOT_LINE /* When using TMD this macro should be undefined */
#endif /* INCLUDE_WDB_COMM_VTMD */
#ifdef FORCE_DEFAULT_BOOT_LINE
#undef INCLUDE_VWARE_LAUNCH
#else
#define INCLUDE_VWARE_LAUNCH
#endif /* FORCE_DEFAULT_BOOT_LINE */
/* Bootline Parameters */ /* : modified */
#define DEFAULT_BOOT_LINE "ene(0,0)host:vxWorks " \
"h=192.166.0.254 " \
"e=192.166.0.2:ffffff00 " \
"g=192.166.0.1 " \
"u=target " \
"pw=target " \
"tn=strong44b0x"
#ifdef INCLUDE_VWARE_LAUNCH
#define VWARE_BOOT_LINE "sng(0,0)host:vxWorks " \
"%s " \
"%s " \
"%s " \
"u=target " \
"tn=targetname"
#endif /* INCLUDE_VWARE_LAUNCH */
/* Memory configuration */
#undef LOCAL_MEM_AUTOSIZE /* run-time memory sizing */
#define LOCAL_MEM_SIZE 0x00100000 /* 1M */
#define USER_RESERVED_MEM 0x0 /* see sysMemTop() */
#define DRAM_TYPE 1 /* 1 - SDRAM, 0 - EDO DRAM */
/*
* Boot ROM is an image written either to EPROM or to a Flash device.
* If a Flash device is used, part of it can be reserved for boot
* parameters etc. (see the Flash section below).
*
* The following parameters are defined here and in the Makefile.
* They must be kept synchronized; effectively config.h depends on Makefile.
* Any changes made here must be made in the Makefile and vice versa.
*
* ROM_BASE_ADRS is the base of the Flash ROM/EPROM.
* ROM_TEXT_ADRS is the entry point of the VxWorks image
* ROM_SIZE is the size of the part of the Flash ROM/EPROM allocated to
* the VxWorks image (block size - size of headers)
*
* Two other constants are used:
* ROM_COPY_SIZE is the size of the part of the ROM to be copied into RAM
* (uncompressed bootrom)
* ROM_SIZE_TOTAL is the size of the entire Flash ROM (used in sysPhysMemDesc)
*
* The values are given as literals here to make it easier to ensure
* that they are the same as those in the Makefile.
*/
#define ROM_BASE_ADRS 0x80000000 /* base of Flash/EPROM 16 MB */
/* : 0x01000000->0x00000000 */
#define ROM_TEXT_ADRS 0x80000000 /* code start addr in ROM */
#define ROM_SIZE 0x00200000 /* size of ROM holding bootRom 512K */
#define ROM_COPY_SIZE ROM_SIZE
#define ROM_SIZE_TOTAL 0x00200000 /* total size of ROM 2MB */
/* : 0x00006000->0x0C001000 */
#define RAM_LOW_ADRS 0x80204000 /* VxWorks image entry point */
/* : 0x00480000->0x0C500000 */
#define RAM_HIGH_ADRS 0xF0000000 /* RAM address for ROM boot */
/*
* Flash memory configuration
*
* If a Flash memory part is fitted instead of an EPROM, part of it can
* be used as NVRAM storage, if desired. If this is wanted, define
* INCLUDE_FLASH and reduce ROM_SIZE in this file and in Makefile by
* NV_RAM_SIZE. The default is not to provide support for Flash.
*/
#undef INCLUDE_FLASH /* : define->undef */
#ifdef INCLUDE_FLASH
#define FLASH_WIDTH 4
#define FLASH_CHIP_WIDTH 2
#define SYS_FLASH_TYPE FLASH_29LV800 /* Specify 16 bit 29F part */
#define FLASH_SEGMENT_SIZE 0x2000 /* sector size at 0xFA000-0xFBFFF */
#define FLASH_ADRS ((SBCARM7_FLASH_BASE + 0xFA000) | 0x4000000) /* non cacheable */
#define FLASH_SIZE FLASH_SEGMENT_SIZE
#undef FLASH_NO_OVERLAY
#undef NV_RAM_ADRS
#undef NV_RAM_INTRVL
#undef NV_RAM_SIZE
#undef NV_BOOT_OFFSET
#define NV_RAM_ADRS FLASH_ADRS
#define NV_RAM_INTRVL 1
#define NV_RAM_SIZE FLASH_SEGMENT_SIZE
#define NV_BOOT_OFFSET (FLASH_SEGMENT_SIZE - 0x200)
#else
#define NV_RAM_SIZE NONE
#endif /* INCLUDE_FLASH */
/* LCD support */
#undef INCLUDE_LCD /* : define->undef */
/* LED support */
#undef INCLUDE_LED /* : define->undef */
#undef BSP_VTS
#ifdef BSP_VTS
#undef INCLUDE_PING
#undef INCLUDE_RLOGIN
#undef INCLUDE_SHOW_ROUTINES
#undef INCLUDE_NET_SYM_TABLE
#define INCLUDE_SHELL
#define INCLUDE_PING
#define INCLUDE_RLOGIN
#define INCLUDE_SHOW_ROUTINES
#define INCLUDE_NET_SYM_TABLE
#endif /*BSP_VTS*/
#undef WDB_COMM_TYPE /* default WDB agent communication path is END */
#define WDB_COMM_TYPE WDB_COMM_END
/* Serial port configuration */
#define INCLUDE_SERIAL
#undef NUM_TTY
#define NUM_TTY N_SIO_CHANNELS
#undef CONSOLE_TTY
#define CONSOLE_TTY 0
/*** WDB ***/
#ifdef SERIAL_DEBUG
#undef DEFAULT_BOOT_LINE /* : added*/
#define DEFAULT_BOOT_LINE "tsfs(0,0)host:vxWorks " \
"h=192.166.0.254 " \
"e=192.166.0.2:ffffff00 " \
"g=192.166.0.1 " \
"u=target " \
"pw=target " \
"tn=strong44b0x " \
"o=ene"
#ifndef INCLUDE_TSFS_BOOT /* : added*/
#define INCLUDE_TSFS_BOOT
#endif
#define WDB_NO_BAUD_AUTO_CONFIG
#undef WDB_COMM_TYPE
#undef WDB_TTY_BAUD
#undef WDB_TTY_CHANNEL
#undef WDB_TTY_DEV_NAME
#define WDB_COMM_TYPE WDB_COMM_SERIAL /* WDB in Serial mode */
/* : 115200->38400 */
#define WDB_TTY_BAUD 38400 /* Baud rate for WDB Connection */
#define WDB_TTY_CHANNEL 1 /* COM PORT #2 */
#define WDB_TTY_DEV_NAME "/tyCo/1" /* default TYCODRV_5_2 device name */
#endif /* SERIAL_DEBUG */
/*
* Cache configuration
*
* Note that when MMU is enabled, cache modes are controlled by
* the MMU table entries in sysPhysMemDesc[], not the cache mode
* macros defined here.
*/
/* De-select unused (default) network drivers selected in configAll.h */
#undef INCLUDE_ENP /* include CMC Ethernet interface*/
#undef INCLUDE_EX /* include Excelan Ethernet interface */
#undef INCLUDE_SM_NET /* include backplane net interface */
#undef INCLUDE_SM_SEQ_ADDR /* shared memory network auto address setup */
/* Enhanced Network Driver (END) Support */
#undef INCLUDE_NETWORK
#undef INCLUDE_END
#undef END_OVERRIDE /* define if you are using old boot ROMs. */
#ifdef INCLUDE_END
/* : INCLUDE_SNGKS32C_END->INCLUDE_NE2000_END */
#define INCLUDE_NE2000_END /* Include Ethernet driver */
#endif /* INCLUDE_END */
#ifdef INCLUDE_SHELL
#define INCLUDE_SYM_TABLE
#define INCLUDE_STANDALONE_SYM_TABLE
#define INCLUDE_LOADER
#define INCLUDE_UNLOADER
#define INCLUDE_NET_SHOW
#endif /* INCLUDE_SHELL */
/*
* Interrupt mode - interrupts can be in either preemptive or non-preemptive
* mode. For non-preemptive mode, change INT_MODE to INT_NON_PREEMPT_MODEL
*/
#define INT_MODE INT_NON_PREEMPT_MODEL
/*
* miscellaneous definitions
* Note: ISR_STACK_SIZE is defined here rather than in ../all/configAll.h
* (as is more usual) because the stack size depends on the interrupt
* structure of the BSP.
*/
#define ISR_STACK_SIZE 0x800 /* size of ISR stack, in bytes */
/* Optional timestamp support */
#undef INCLUDE_TIMESTAMP
#undef INCLUDE_WINDVIEW
#undef INCLUDE_INSTRUMENTATION
#define INCLUDE_DOSFS
#define INCLUDE_RAMDRV
/* Optional TrueFFS support */
/* : undef->define */
#undef INCLUDE_TFFS /* to include TrueFFS driver */
#ifdef INCLUDE_TFFS
#define INCLUDE_MTD_SST39VF160 /* : added */
#define INCLUDE_SHOW_ROUTINES
#define INCLUDE_DOSFS
#endif /* INCLUDE_TFFS */
/*
* There isn't MMU support in this BSP, this macro is to
* force the MMU to be disable.
*/
#undef INCLUDE_MMU_BASIC
/*
* For cache support define this macro
*/
#undef INCLUDE_CACHE_SUPPORT
/* -以下是自己定制的宏定义 */
#undef RAM_SIM /* 是否用SDT仿真 */
#undef SYS_CLK_RATE /* 设置系统时钟频率，缺省60 */
#define SYS_CLK_RATE 100
#undef CONSOLE_BAUD_RATE
#define CONSOLE_BAUD_RATE 9600 /* bootRom Shell 波特率，缺省9600 */
#define INCLUDE_FTP_SERVER /* 启动目标机FTP服务 */
#undef INCLUDE_BOOTP /* 裁减映象大小，节省约20K */
#define Fosc 11059200
#define Fcclk (Fosc * 4)
#define Fcco (Fcclk * 4)
#define Fpclk (Fcclk / 4) * 1
/* -以上是自己定制的宏定义 */
#include "wrSbcArm7.h"
#ifdef __cplusplus
}
#endif
#endif /* INCconfigh */
#if defined(PRJ_BUILD)
#include "prjParams.h"
#endif