www.pudn.com > RC500.rar > m500a.h
#ifndef M500A_H
#define M500A_H
// P I C C - C O M M A N D S
// commands which are handled by the tag
// Each tag command is written to the reader IC and transfered via RF
#define PICC_REQSTD 0x26 // request idle
#define PICC_REQALL 0x52 // request all
#define PICC_ANTICOLL1 0x93 // anticollision level 1
#define PICC_ANTICOLL2 0x95 // anticollision level 2
#define PICC_ANTICOLL3 0x97 // anticollision level 3
#define PICC_AUTHENT1A 0x60 // authentication step 1
#define PICC_AUTHENT1B 0x61 // authentication step 2
#define PICC_READ 0x30 // read block
#define PICC_WRITE 0xA0 // write block
#define PICC_DECREMENT 0xC0 // decrement value
#define PICC_INCREMENT 0xC1 // increment value
#define PICC_RESTORE 0xC2 // restore command code
#define PICC_TRANSFER 0xB0 // transfer command code
#define PICC_HALT 0x50 // halt
//////////////////////////////////////////////////////////////////////
// Mifare Error Codes
// Each function returns a status value, which corresponds to the
// mifare error codes.
#define MI_OK 0
#define MI_CHK_OK 0
#define MI_CRC_ZERO 0
#define MI_CRC_NOTZERO 1
#define MI_NOTAGERR (-1)
#define MI_CHK_FAILED (-1)
#define MI_CRCERR (-2)
#define MI_CHK_COMPERR (-2)
#define MI_EMPTY (-3)
#define MI_AUTHERR (-4)
#define MI_PARITYERR (-5)
#define MI_CODEERR (-6)
#define MI_SERNRERR (-8)
#define MI_KEYERR (-9)
#define MI_NOTAUTHERR (-10)
#define MI_BITCOUNTERR (-11)
#define MI_BYTECOUNTERR (-12)
#define MI_IDLE (-13)
#define MI_TRANSERR (-14)
#define MI_WRITEERR (-15)
#define MI_INCRERR (-16)
#define MI_DECRERR (-17)
#define MI_READERR (-18)
#define MI_OVFLERR (-19)
#define MI_POLLING (-20)
#define MI_FRAMINGERR (-21)
#define MI_ACCESSERR (-22)
#define MI_UNKNOWN_COMMAND (-23)
#define MI_COLLERR (-24)
#define MI_RESETERR (-25)
#define MI_INITERR (-25)
#define MI_INTERFACEERR (-26)
#define MI_ACCESSTIMEOUT (-27)
#define MI_NOBITWISEANTICOLL (-28)
#define MI_QUIT (-30)
#define MI_RECBUF_OVERFLOW (-50)
#define MI_SENDBYTENR (-51)
#define MI_SENDBUF_OVERFLOW (-53)
#define MI_BAUDRATE_NOT_SUPPORTED (-54)
#define MI_SAME_BAUDRATE_REQUIRED (-55)
#define MI_WRONG_PARAMETER_VALUE (-60)
#define MI_BREAK (-99)
#define MI_NY_IMPLEMENTED (-100)
#define MI_NO_MFRC (-101)
#define MI_MFRC_NOTAUTH (-102)
#define MI_WRONG_DES_MODE (-103)
#define MI_HOST_AUTH_FAILED (-104)
#define MI_WRONG_LOAD_MODE (-106)
#define MI_WRONG_DESKEY (-107)
#define MI_MKLOAD_FAILED (-108)
#define MI_FIFOERR (-109)
#define MI_WRONG_ADDR (-110)
#define MI_DESKEYLOAD_FAILED (-111)
#define MI_WRONG_SEL_CNT (-114)
#define MI_WRONG_TEST_MODE (-117)
#define MI_TEST_FAILED (-118)
#define MI_TOC_ERROR (-119)
#define MI_COMM_ABORT (-120)
#define MI_INVALID_BASE (-121)
#define MI_MFRC_RESET (-122)
#define MI_WRONG_VALUE (-123)
#define MI_VALERR (-124)
#define GetRegPage(addr) (0x80 | (addr>>3))
#define nocard 0
#define mifare1S50 1
#define mifare1S70 2
#define mifarelight 3
#define unknowncard 4
// write data to address 写一个数据到某个地址
///////////////////////////////////////////////////////////////////////
void WriteRawIO(unsigned char Address,unsigned char value);
// read data from address 从某个地址读出一个数据
///////////////////////////////////////////////////////////////////////
unsigned char ReadRawIO(unsigned char Address);
// write data eeprom 往一个地址写一个数据(EEPROM)
///////////////////////////////////////////////////////////////////////
void WriteIO(unsigned char Address, unsigned char value);
// read data eeprom 从一个地址读出一个数据(EEPROM)
///////////////////////////////////////////////////////////////////////
unsigned char ReadIO(unsigned char Address);
// Set pcd time 设置定时时间
///////////////////////////////////////////////////////////////////////
void M500PcdSetTime(unsigned char timeLength);
// Request Command defined in ISO14443(Mifare) 定义mifare 请求命令
///////////////////////////////////////////////////////////////////////
char M500PcdCmd(unsigned char cmd,
volatile unsigned char data *rcv,
MfCmdInfo idata *info);
// Set bit 置一个bit
///////////////////////////////////////////////////////////////////////
char SetBitMask(unsigned char reg,unsigned char mask);
// Clear bit 清一个bit
///////////////////////////////////////////////////////////////////////
char ClearBitMask(unsigned char reg,unsigned char mask);
//清除FIFO
///////////////////////////////////////////////////////////////////////
void FlushFIFO(void);
// Value format operations for Mifare Standard card ICs 操作值设置
///////////////////////////////////////////////////////////////////////
char M500PiccValue(unsigned char dd_mode,
unsigned char addr,
unsigned char *value,
unsigned char trans_addr);
// Set card in HALT-state 终止卡的操作
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
// Key loading into the MF RC500's EEPROM
// 校验卡密码(E2)
///////////////////////////////////////////////////////////////////////
char M500PiccAuthE2( unsigned char auth_mode,unsigned char *snr,
unsigned char keynr,unsigned char block);
///////////////////////////////////////////////////////////////
// Key loading into the MF RC500's EEPROM
///////////////////////////////////////////////////////////////
char M500PcdLoadKeyE2(unsigned char key_type,
unsigned char sector,
unsigned char *uncoded_keys);
////////////////////////////////////////////////////////////////
// Read the mifare card
// 读卡
////////////////////////////////////////////////////////////////
char M500PiccRead(unsigned char addr,unsigned char *_data);
// Write the mifare card
// 写卡 下载密码
////////////////////////////////////////////////////////////////
char M500PiccWrite( unsigned char addr,unsigned char *_data);
char MfConfig(void);
// Set card in HALT-state 终止卡的操作
///////////////////////////////////////////////////////////////////////
char M500PiccHalt(void);
// Reset Card 复位卡
///////////////////////////////////////////////////////////////////////
char M500PcdRfReset(unsigned char ms);
// Authentication key coding
///////////////////////////////////////////////////////////////////////
char M500HostCodeKey(unsigned char *uncoded,
unsigned char *coded);
// Request Command defined in ISO14443(MIFARE)
// Request
// 寻卡
///////////////////////////////////////////////////////////////////////
char M500PiccCommonRequest(unsigned char req_code,
unsigned char *atq);
// Cascaded Anti-Collision Command defined in ISO14443(MIFARE)
// 防冲突 读卡的系列号 MLastSelectedSnr
///////////////////////////////////////////////////////////////////
char M500PiccCascAnticoll( unsigned char bcnt,
unsigned char *snr);
char M500PiccCascSelect(unsigned char *snr,
unsigned char *sak);
// Set bit 置一个bit
///////////////////////////////////////////////////////////////////////
char SetBitMask(unsigned char reg,unsigned char mask);
// Set pcd time 设置定时时间
///////////////////////////////////////////////////////////////////////
void M500PcdSetTmo(unsigned char tmoLength);
// Request Command defined in ISO14443(Mifare) 定义mifare 请求命令
///////////////////////////////////////////////////////////////////////
char M500PcdCmd(unsigned char cmd,
volatile unsigned char data * rcv,
volatile MfCmdInfo idata *info);
// Clear bit 清一个bit
///////////////////////////////////////////////////////////////////////
char ClearBitMask(unsigned char reg,unsigned char mask);
//清除FIFO
///////////////////////////////////////////////////////////////////////
void FlushFIFO(void);
// Write the MF RC500's EEPROM
///////////////////////////////////////////////////////////////////////
char PcdWriteE2(unsigned int startaddr,
unsigned char length,
unsigned char* _data);
//认证状态
///////////////////////////////////////////////////////////////////////
char M500PiccAuthState(unsigned char auth_mode,
unsigned char *snr,
unsigned char block);
//////////////////////////////////////////////////////////////////////////////
#endif
//////////////////////////////////////////////////////////////////////////////
// End of File
//////////////////////////////////////////////////////////////////////////////