www.pudn.com > at90usb128-demo-cdc-1_0_3.zip > conf_usb.h
//! @file conf_usb.h,v
//!
//! Copyright (c) 2006 Atmel.
//!
//! Please read file license.txt for copyright notice.
//!
//! This file contains the possible external configuration of the USB
//!
//!
//! @version 1.1 at90usb128-demo-cdc-1_0_3 $Id: conf_usb.h,v 1.1 2006/03/14 18:01:23 rletendu Exp $
//!
//! @todo
//! @bug
#ifndef _CONF_USB_H_
#define _CONF_USB_H_
//! @defgroup usb_general_conf USB application configuration
//!
//! @{
// _________________ USB MODE CONFIGURATION ____________________________
//
//! @defgroup USB_op_mode USB operating modes configuration
//! defines to enable device or host usb operating modes
//! supported by the application
//! @{
//! @brief ENABLE to activate the host software library support
//!
//! Possible values ENABLE or DISABLE
#define USB_HOST_FEATURE DISABLED
//! @brief ENABLE to activate the device software library support
//!
//! Possible values ENABLE or DISABLE
#define USB_DEVICE_FEATURE ENABLED
//! @}
// _________________ USB REGULATOR CONFIGURATION _______________________
//
//! @defgroup USB_reg_mode USB regulator configuration
//! @{
//! @brief Enable the internal regulator for USB pads
//!
//! When the application voltage is lower than 3.5V, to optimize power consumption
//! the internal USB pads regulatr can be disabled.
#ifndef USE_USB_PADS_REGULATOR
#define USE_USB_PADS_REGULATOR ENABLE // Possible values ENABLE or DISABLE
#endif
//! @}
// _________________ HOST MODE CONFIGURATION ____________________________
//
//! @defgroup USB_host_mode_cfg USB host operating mode configuration
//!
//! @{
#define HID_CLASS 0x03
#define MS_CLASS 0x08
//! @brief VID/PID supported table list
//!
//! This table contains the VID/PID that are supported by the reduced host application
//! VID_PID_TABLE format definition:
//!
//! #define VID_PID_TABLE {VID1, number_of_pid_for_this_VID1, PID11_value,..., PID1X_Value \n
//! ...\n
//! ,VIDz, number_of_pid_for_this_VIDz, PIDz1_value,..., PIDzX_Value}
#define VID_PID_TABLE {0x03EB, 2, 0x201C, 0x2014 \
,0x0123, 3, 0x2000, 0x2100, 0x1258}
//! @brief CLASS/SUBCLASS_PROTOCOL supported table list
//!
//! This table contains the CLASS/SUBCLASS/PROTOCOL that is supported by the reduced host application
//! This table definition allows to extended the reduced application device support to an entire Class/
//! /subclass/protocol instead of a simple VID/PID table list.
//!
//! CLASS_SUBCLASS_PROTOCOL format definition: \n
//! #define CLASS_SUBCLASS_PROTOCOL {CLASS1, SUB_CLASS1,PROTOCOL1, \n
//! ...\n
//! CLASSz, SUB_CLASSz,PROTOCOLz}
#define CLASS_SUBCLASS_PROTOCOL {0x0A, 0x00, 0x00, \
0x00, 0x00, 0x00,\
0xFF,0x00,0x00}
//! The size of RAM buffer reserved of descriptors manipulation
#define SIZEOF_DATA_STAGE 250
//! The address that will be assigned to the connected device
#define DEVICE_ADDRESS 0x05
//! The host controller will be limited to the strict VID/PID list.
//! When enabled, if the device PID/VID does not belongs to the supported list,
//! the host controller library will not go to deeper configuration, but to error state.
#define HOST_STRICT_VID_PID_TABLE DISABLE
//! Try to configure the host pipe according to the device descriptors received
#define HOST_AUTO_CFG_ENDPOINT ENABLE
//! Host start of frame interrupt always enable
#define HOST_CONTINUOUS_SOF_INTERRUPT DISABLE
//! When Host error state detected, goto unattached state
#define HOST_ERROR_RESTART ENABLE
//! Force WDT reset upon ID pin change
#define ID_PIN_CHANGE_GENERATE_RESET DISABLE
//! NAK handshake in 1/4sec (250ms) before timeout
#define NAK_TIMEOUT_DELAY 1
#if (HOST_AUTO_CFG_ENDPOINT==FALSE)
//! If no auto configuration of EP, map here user function
#define User_configure_endpoint()
#endif
//! @defgroup host_cst_actions USB host custom actions
//!
//! @{
// write here the action to associate to each USB host event
// be carefull not to waste time in order not disturbing the functions
#define Usb_id_transition_action()
#define Host_device_disconnection_action()
#define Host_device_connection_action()
#define Host_sof_action()
#define Host_suspend_action() host_suspend_action();
#define Host_hwup_action()
#define Host_device_not_supported_action()
#define Host_device_supported_action()
#define Host_device_error_action()
//! @}
extern void host_suspend_action(void);
//! @}
// _________________ DEVICE MODE CONFIGURATION __________________________
//! @defgroup USB_device_mode_cfg USB device operating mode configuration
//!
//! @{
#define NB_ENDPOINTS 4 //! number of endpoints in the application including control endpoint
#define TX_EP 0x01
#define RX_EP 0x02
#define INT_EP 0x03
#define Usb_unicode(a) ((U16)(a))
//! @defgroup device_cst_actions USB device custom actions
//!
//! @{
// write here the action to associate to each USB event
// be carefull not to waste time in order not disturbing the functions
#define Usb_sof_action() sof_action();
#define Usb_wake_up_action()
#define Usb_resume_action()
#define Usb_suspend_action() suspend_action();
#define Usb_reset_action()
#define Usb_vbus_on_action()
#define Usb_vbus_off_action()
#define Usb_set_configuration_action()
//! @}
extern void sof_action(void);
extern void suspend_action(void);
//! @}
//! @}
#endif // _CONF_USB_H_